Choosing a Rooflight for a Flat Roof Extension

Flat extension roof adjoining a tiled roof

What should a flat roof rooflight do?

Choose a flat roof rooflight by matching the product to the measured fall of the roof, deciding whether it needs to open and checking how the frame will meet the waterproofing. Start with the room below. If the aim is to light a kitchen worktop, placement and glare deserve as much attention as the size of the opening. If the room needs summer purge ventilation, consider whether an opening model is worth the extra controls and access requirements.

A rooflight positioned deep inside a rear extension can bring daylight to the part of the room furthest from the garden doors. Draw the furniture and internal layout on the plan before settling on the opening. A smaller, well-placed unit can serve the task better than a larger unit centred on the roof. Compare the visible glass area quoted by each supplier because the outside frame dimensions include components that do not admit daylight.

Flat glass, curved glass or a dome?

Start with the installation limits for the exact model. VELUX specifies its Standard glass flat roof window for pitches of 2° to 15°, while it offers a curved glass model suitable for a roof pitch of 0°. That is a product-specific example. Ask the installer to measure the slope at the proposed opening and show how it meets the glazing manufacturer’s instructions. The permitted pitch for a window does not determine how the rest of the roof needs to drain.

Flat glass can give a low-profile appearance when seen from upstairs. Curved glazing helps water drain from the glass and gives the unit a different profile. A dome is another option where the shape and glazing specification suit the room. Compare what you will see from inside, from upstairs and from adjoining properties. It helps to request the actual section drawing rather than trying to infer the depth of the frame from a photograph.

VELUX flat roof window ranges and pitch guidance

Fixed or opening glazing?

A fixed unit suits a room that already has a workable ventilation plan and needs more daylight. An opening unit can help release warm air collected at ceiling level when there is a lower opening for replacement air. For a high ceiling, ask how you will operate it and what happens if it is left open in a shower. If you choose powered operation, have the roofer and electrician agree on the cable route before the ceiling is finished.

Think about direct sunlight separately. A large opening can create glare on an island or a screen and increase summertime heat gain. Ask what solar-control glazing or blinds are compatible with the model. Also request the declared thermal performance of the whole unit and compare it on the same basis between suppliers. The thermal figure for the centre of the pane alone leaves out the effect of the frame.

The English Housing Survey’s July 2026 weather resilience release found that the share of occupied homes in England where households reported overheating rose from 7% in 2019 to 12% in 2024. The survey covers whole homes. For an extension with a large area of overhead glass, use the design stage to consider summer shading and ventilation together.

English Housing Survey figures on overheating

How does the roof stay watertight?

The upstand is the raised perimeter the membrane seals to beneath the frame. Ask who supplies it, whether it is insulated and how the waterproofing will turn up and terminate against it. Decide these details alongside the depth of the finished roof, especially if new insulation will raise the surrounding surface. A rooflight ordered against the depth of the old roof can leave the wrong clearance once the new build-up goes down.

Allow room around the opening for a contractor to make the waterproofing details and later inspect them. Look at where water will travel around the upstand and whether the unit interrupts the route to an outlet. On an existing roof, find out how the structural opening will be formed and supported before placing an order. The joists and their spans may affect both the position and the cost.


Looking for roofing services near you?

Excellent Building & Roofing provides roofing services in these areas:


What should be included in the quote?

Ask for the model and size, a roof section showing the upstand and membrane connection, and the work needed to form the opening. Clarify whether lifting the unit into place, electrical connection and internal plaster finishing are included. Check who will protect the opening if the job runs across days of unsettled weather. If the roof is being recovered at the same time, ask who is responsible for the junction under the waterproofing guarantee.

For an existing extension, establish how much of the surrounding covering must be lifted and whether its condition makes local work practical. Ask what happens if the deck or supporting timber is damaged when opened up. At handover, keep the window specification, guarantee terms and photographs of the concealed waterproofing. For an opening unit, ask the installer to demonstrate the controls and explain how to clean or service the glazing safely.


Summary

Start with the room’s daylight and ventilation needs, then check that the exact rooflight suits the measured pitch. Agree how the opening will be supported and waterproofed before ordering the window. If the rooflight is going into an existing extension, have its roof covering and upstand assessed together.

Flat roofing for rooflight installations